Press an input selector button to select the source component containing the function you want to clear. The selected component name appears in the display window. Page Zone 2 U. If you own these products, you may not need to use an infrared emitter. Remote controlling Zone 2 The supplied remote control can be used to control Zone 2. Page 89 Press an input selector button to select the input source you want to listen to in the second room. Page Editing Sound Field Parameters The acoustics in your room could be changed to those of a concert hall, a dance floor, or virtually any size room at all.
Changing parameter settings You can enjoy good quality sound with the factory preset parameters. Not all of the following parameters are found in every program. Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one which has highly reflective surfaces. This changes the apparent size of the acoustic environment over an extremely wide range. LIFT Dialog lift Function: Adjusts the height of the front and center channel sounds by assigning some of the front and center channel elements to the presence speakers.
Description: The larger the parameter, the higher the position of the front and center channel sound. Control range: 0 to 1. Page Troubleshooting Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.
The sleep timer has turned the unit off. The sound is muted. Only the speaker on Incorrect cable connections. Dolby Digital signals. The picture is The video source uses scrambled or disturbed.
Page Remote control Problem The remote control Wrong distance or angle. Direct sunlight or lighting from an inverter type of fluorescent lamp, etc. The batteries are weak. The manufacturer code was not correctly set.
Be sure this unit is in standby mode. Page Glossary Audio formats Dolby Digital Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio.
With 3 front channels left, center, and right , and 2 surround stereo channels, Dolby Digital provides 5 full-range audio channels. With an additional channel especially for bass effects, called LFE low frequency effect , the system has a total of 5. Good luck to the repair! Please do not offer the downloaded file for sell only use it for personal usage! Looking for similar yamaha manual?
Document preview [1st page]. Please tick the box below to get download link:. For this no need registration. One cable is colored or shaped differently, perhaps with a stripe, groove or ridges. Connect the striped grooved, etc. With the exception of U. Open the tab, then insert one banana plug connector into the hole of each terminal. Do not attempt to close the tabs after connecting the banana plugs.
You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously. They do not output sound when other sound fields are selected. Connect one or two speaker systems 6, 7 to these terminals.
Connect surround back speakers 9, 10 to these terminals. If you only connect one surround back speaker, connect it to the left L terminals. Do not connect this unit or other components to the mains power until all connections between components are complete. You can input analog signals from audio components by connecting audio pin cable to the analog jacks on this unit.
Connect red plugs to the right jacks and white plugs to the left jacks. This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. All digital input jacks are compatible with kHz sampling digital signals. This unit handles digital and analog signals independently.
Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust. This unit has three types of video jacks. Connection depends on the availability of input jacks on your monitor.
For S-Video signals, separated into luminance Y and color C video signals to achieve high-quality color reproduction. For component signals, separated into luminance Y and color difference P B , P R to provide the best quality in picture reproduction. Be sure to match the left and right outputs to the left and right input jacks for the front and surround channels. We recommend that you connect at least a 5. When recording, you must make the same type of video connections i.
If you have a turntable with a low-output MC cartridge, use an in-line boosting transformer or MC-head amplifier when connecting to these jacks.
Connect your turntable to the GND terminal to reduce noise in the signal. However you may hear less noise without the connection to the GND terminal for some record players. If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the PRE OUT jacks as follows.
Set the volume of the amplifier connected to this unit to the maximum. Both FM and AM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground.
A good earth ground is a metal stake driven into moist earth. Be sure to set the frequency step according to the frequency spacing in your area see page If you experience poor reception quality, an outdoor antenna may improve the quality.
Use these outlets to connect the power cords from your other components to this unit. The outlet s supply power to any connected component whenever this unit is turned on. Voltages are:. The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However if the power cord is disconnected from the AC wall outlet, or the power supply is cut for more than one week, the stored data will be lost. If you are using 4 or 6 ohm speakers, set the impedance to 4 or 6 ohms as follows before turning on the power.
The supplied optimizer microphone collects and analyzes the sound your speakers produce in your actual listening environment. YPAO performs the following checks and makes appropriate adjustments to give you the best possible sound from your system. Checks the distance of each speaker from the listening position and adjusts the delay of each channel so that the sound from each speaker reaches the listening position at the same time.
Also checks the phase of each speaker. This is particularly important if you use different brands or sizes of speakers for some channels or have a room with unique sonic characteristics. YPAO equalizing calibration incorporates three parameters frequency, level and Q factor for each of the seven bands in its parametric equalizer to provide highly precise automatic adjustment of frequency characteristics.
If possible, use a tripod etc. You can display the detailed result information by using d and. If you are not satisfied with the result or want to manually adjust each setup parameter, use the manual setup parameters see page Warnings will not cancel the auto setup. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.
Please check your email for further instructions. Enter a new password. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e If the product has been dropped or damaged in any way, and f When the product exhibits a distinct change in perfor- mance - this indicates a need for service.
Built-in 7-channel power amplifier Minimum RMS output power 0. Please check that you received all of the following parts. Installing batteries in the remote control 2 1 3 1 Press the part and slide the battery compartment cover off. Note In standby mode, this unit consumes a small amount of power in order to receive infrared-signals from the remote control. Selects the speaker channel to be adjusted when the unit is not in tuner mode. Switches the reception band when the unit is in tuner mode.
BS2 : BS3 : BS4 : BS5 : BS6 : BS7 : BS8 : MTT : Immediately after the power is turned on, measure the 1. Filament 2 NP No Pin 3 NX Decoder No. Back Surr.
0コメント